I have created a report using Matrix and I have set the property "Keep together on One Page if Possible" to show the report in one page.But for some reason the reprot is not showing all the result rows,I see half hidden row.See screeshot
Related
I have an SSRS report that has a main tablix which contains a header (appears only once per group) and a "group by" field for the second tablix located inside the main tablix.
The issue: when Tablix 2 data does not entirely fit on the page, it'll jump to the second page on PDF print, leaving first page containing only the header without data (SSRS preview shows it correctly).
I'd like Tablix 2 data to start on the first page and display on the second page whatever left.
Please note there are no forced page breaks or "keep together" options checked.
I have inherited an SSRS report which had an existing tablix on it - I want to add a further tablix below to display data from another data set as the format is very slightly different - each tablix displays a different kind of sales for a certain customer.
I have added the second tablix and the report seems fine within the report designer renderer, but when I access it via MS Edge directly from the URL the first tablix overlaps the second and obscures it from view.
I have set a page break at the end of the first tablix, and at the start of the second, and again in the designer renderer it works fine and pages, but in MS Edge it overlaps across the page break. In Chrome it renders OK.
The issue I have is I am displaying this SSRS report in a Web Browser Control on an access for an it renders just like it does in MS Edge so it looks screwed up.
It is like the first tablix just runs over into page 2 rather than making the extra content of itself page 2, and the second tablix then on page 3. I don't even really need the pages as ideally it would all be one long report with a vertical scroll, but this overlap issue means I have been trying to force it to split.
Any other way I can stop the first tablix obliterating the second one?
I had a similar problem recently (I found your question while searching for an answer). I didn't want to go to all the trouble of creating a sub report and eventually tracked down the cause of the issue for my case which may be the same as what you were experiencing.
The issue was that my first Tablix was setup with a height of 2.7cm. My second one's top was 2.66781cm. That caused both of them to overlap with each other when the report was rendered. When I changed the top of the second Tablix to 2.7cm the issue was resolved.
While working with Tablix Report I want to visible Group header while scrolling
I tried Fixed Data = True but not working for me. BTW, First header row is working fine by changes of show scroll bar. (FixedData property to True in Advanced Mode) but not the this one row.
Kindly provide me the solution.
In SSRS 2008 R2, I managed a workaround using subreports.
Make a report that shows the data for a single group, based on a parameter.
Put all the headers you want on this report's tablix, and make them fixed with FixedData = True.
Use the parameter to set what will appear in the group-specific header text.
Make a separate report that will get every group.
Create a table grouped by your group, with one cell.
Put a Subreport in the cell, and pass the group to the subreport's parameter.
This worked for me in the Visual Studio preview, and viewing a deployed version on IE and Chrome, and hopefully will work in your environment too.
The catch is you'll see the main report header repeated for each group. However I tried to add this to the main report and it seemed to confuse matters, functioning differently in preview, IE and Chrome.
I am using MS Report builder 3.0 to create one of my report.The report is the tabular report and sometimes the size of table grows long about 2 to 3 pages.
But i want to show the entire report with in single page without having to click next page button. I tried increasing page size but that doesnot work. Please help! I am new to Report Builder.
It sounds like you need to set the InteractiveSize -> Height property to 0cm:
This will prevent implicit page breaks when viewed in Report Manager or a ReportViewer control.
This won't have any effect on printing, exporting to PDF, etc, as these media have to force page breaks no matter what - they're affected by the PageSize properties.
I have few subreports in a sql main report(.rdl file) using VS/SSRS 2008.
The subreports start approximately on the middle of the page in the main report detail section. I have one group in main report, shows header information and pass one parameter - ReportID to each subreport.
I also have checked both:
Row Headers – “Repeat header rows on each page” and
Column Headers – “Repeat header columns on each page”
on General tab of Tablix properties of the main report.
If I have few detail lines in the subreport, so that all can be rendered on page one, everything is ok.
If I have more detail lines in the subreport so that it's not possible to print all on one page, the subreport renders from the fist page and moves on to page two, three and so on.
When I have more than one page of data in the subreport, it is also started on page one, and continues renders on second page and so on...
However, it doesn't show the main report's column/row headers on subsequent pages of the subreports?
I've noticed that when next item/ReportID starts in my main report group, it prints column header only on the first page but not any subsequent page and so on...
I also tried to check only ONE, either
Row Headers – “Repeat header rows on each page” OR
Column Headers – “Repeat header columns on each page”
on general tab of Tablix properties of the main report BUT didn’t work?
Any ideas how to print header info on each page when subreport has more than one page data?
Pagination is always fun in SSRS.
Have you looked at the page size/interactive of the subreport? This may stop the subreport paging, but I don't know if it's what you want.
An older article on pagination
And a newer one
Presently I am encountering the same problem. In a previous SSRS report we got it to work by putting our tablix inside a single-cell list item so that the headers were repeated. Now I am working on a different report, and when I try the same thing I'm getting this error:
[rsInvalidDetailDataGrouping] The tablix ‘tablixOpportunitySummary’ has a detail member with inner members. Detail members can only contain static inner members.
I've searched extensively, but this is the only link which indicates an known problem in SSRS. At the time of this post it contained 4 workarounds:
https://connect.microsoft.com/SQLServer/feedback/details/337720/katmai-reporting-services-2008-tablix-control-repeat-column-headers-does-not-work#
A little late, but I think this is what you are looking for:
You need to go to tablix properties > General and check the option Keep header visible while scrolling. Then go to column/row groups in the advanced mode, chose your static row and set the Fixed Data mode to True, Repeat on new page to True and Keep with group to After.
Here is probably the best reference: Here