I'm experiencing a serious headache while trying to create a stored procedure.
DELIMITER $$
create PROCEDURE insertDummyUser(rank int unsigned)
BEGIN
INSERT INTO tbl (name, rank) VALUES ('DummyUser', rank);
END$$
It gives me the following error:
1064 - You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near '' at line 5
I just cant wrap my head around this. It looks fine to me.
I'm just starting out with these stored procedures, so any help at all is greatly appreciated :)
The following stored procedure runs smoothly:
DELIMITER $$
CREATE PROCEDURE `insertDummyUser`(`p_rank` INT UNSIGNED)
BEGIN
INSERT INTO `tbl` (`name`, `rank`) VALUES ('DummyUser', `p_rank`);
END$$
DELIMITER ;
Related
I'm trying to create a stored_procedure using the following sql code:
INSERT INTO users (name,surname,email,phone,address_id)
VALUES (name,surname,email,phone,address_id);
SET #GeneratedUserID = LAST_INSERT_ID();
INSERT INTO user_login (username,password_salt,hash_code,users_user_id)
VALUES (username,password_salt,hash_code,#GeneratedUserID );
INSERT INTO user_roles (user_id,role_id)
VALUES (#GeneratedUserID ,1);
However, I'm getting an error:
MySQL said: #1064 - You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'SET #GeneratedUserID = LAST_INSERT_ID(); INSERT INTO user_login (username,pas' at line 4
You most likely haven't changed the delimiter, but can't tell for sure, because you didn't post the whole code (please always do this). Therefore MySQL thinks, that the procedure is finished after the first ;.
Your procedure should look like this:
delimiter $$
create procedure x(in p_param1 int, in p_param2 int)
begin
statement1;
statement2;
end$$
delimiter ;
Also note, that you should choose parameter names that are not the same as column names. Best practice is to use a prefix like p_. Same for variables. Use a prefix like v_ or something.
I'm trying create a simple stored procedure in mysql, In this stored procedure I'm trying to call a view and page it.
delimiter //
CREATE PROCEDURE SelectSearchResultsContract (start int, quantity int)
BEGIN
select
searchresultsdisplayview.CompanyName,
searchresultsdisplayview.LastChanceDate,
searchresultsdisplayview.PhoneNumber,
searchresultsdisplayview.ContactName,
searchresultsdisplayview.City,
searchresultsdisplayview.State
FROM searchresultsdisplayview -- this is a view
OFFSET start
LIMIT quantity ;
END
//
delimiter ;
I cannot create this because of the syntax. says I'm missing a simicolon.
I have create many that we like this using tables but the view doesnt like it. Can someone please tell me what I am missing.
EXACT ERROR:
Error Code: 1064. You have an error in your SQL syntax; check the manual that corresponds to your MariaDB server version for the right syntax to use near 'start LIMIT quantity' at line 15
I Figured this out by right clicking and adding stored procedure then copy and paste the sql that it displayed. below is anwser:
DELIMITER $$
USE `construction_bid_source`$$
CREATE PROCEDURE `SelectSearchResultsContract` (quantity int, start int)
BEGIN
select
searchresultsdisplayview.CompanyName,
searchresultsdisplayview.LastChanceDate,
searchresultsdisplayview.PhoneNumber,
searchresultsdisplayview.ContactName,
searchresultsdisplayview.City,
searchresultsdisplayview.State
FROM searchresultsdisplayview
LIMIT quantity-- this is a view
OFFSET start;
END$$
DELIMITER ;
I am having a lot of trouble with the syntax of this stored procedure that is supposed to return All information from a table called Country and is trying to use a parameter for comparison:
Create Procedure CountrybyPK (country char(50))
begin
Select * From Country
Where Country.Name=country
end;
The error I get states:
You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'end' at line 5
You need a statement delimiter between the SELECT statement and END.
Create Procedure CountrybyPK (country char(50))
begin
Select * From Country
Where Country.Name=country;
end;
But since the delimiter would also terminate the whole procedure, you need to use the DELIMITER command to switch to another delimiter:
DELIMITER $$
Create Procedure CountrybyPK (country char(50))
begin
Select * From Country
Where Country.Name=country;
end$$
But since your procedure only has one statement in it, you don't need begin and end at all, you can just do:
Create Procedure CountrybyPK (country char(50))
Select * From Country
Where Country.Name=country;
I am trying to write an simple stored procedure to just print out information from three different tables. The problem is that for some reason \G does not work from within a stored proc. I want the output to be readable so this is pretty important
This code works but doesnt display columns in an effective way
DELIMITER //
DROP PROCEDURE IF EXISTS `snapshot`//
CREATE PROCEDURE snapshot(IN employeeUsername varchar(255))
BEGIN
SELECT * FROM employee where username = employeeUsername;
END //
DELIMITER ;
This code throws an exception
DELIMITER //
DROP PROCEDURE IF EXISTS `snapshot`//
CREATE PROCEDURE snapshot(IN employeeUsername varchar(255))
BEGIN
SELECT * FROM employee where username = employeeUsername \G;
END //
DELIMITER ;
ERROR 1064 (42000): You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near '' at line 3
Any help would be greatly appreciated
\G is an command in MySQL Client and subsequently can not be called from a sql stored proc
I try to create trigger in MySql but get the following error:
#1064 - You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'DELIMITER' at line 1
DELIMITER $$
CREATE TRIGGER library_update
AFTER UPDATE ON wq6vt_vehiclemanager_vehicles
FOR EACH ROW
BEGIN
INSERT IGNORE INTO wq6vt_vehiclemanager_library (maker, model) VALUES(NEW.maker, NEW.vmodel);
INSERT INTO wq6vt_vehiclemanager_library_data (co2_class)
SELECT co2_class FROM wq6vt_vehiclemanager_vehicles
WHERE maker = NEW.maker AND vmodel = NEW.vmodel;
END $$
DELIMITER;
The first query in the trigger do not lead to errors, but second one does. There is some problem with SELECT inside of INSERT ...I think so
there should be a space between the keyword and the symbol,
DELIMITER ;
-- ^ space in between here