Related
I'm in a computer systems course and have been struggling, in part, with two's complement. I want to understand it, but everything I've read hasn't brought the picture together for me. I've read the Wikipedia article and various other articles, including my text book.
What is two's complement, how can we use it and how can it affect numbers during operations like casts (from signed to unsigned and vice versa), bit-wise operations and bit-shift operations?
Two's complement is a clever way of storing integers so that common math problems are very simple to implement.
To understand, you have to think of the numbers in binary.
It basically says,
for zero, use all 0's.
for positive integers, start counting up, with a maximum of 2(number of bits - 1)-1.
for negative integers, do exactly the same thing, but switch the role of 0's and 1's and count down (so instead of starting with 0000, start with 1111 - that's the "complement" part).
Let's try it with a mini-byte of 4 bits (we'll call it a nibble - 1/2 a byte).
0000 - zero
0001 - one
0010 - two
0011 - three
0100 to 0111 - four to seven
That's as far as we can go in positives. 23-1 = 7.
For negatives:
1111 - negative one
1110 - negative two
1101 - negative three
1100 to 1000 - negative four to negative eight
Note that you get one extra value for negatives (1000 = -8) that you don't for positives. This is because 0000 is used for zero. This can be considered as Number Line of computers.
Distinguishing between positive and negative numbers
Doing this, the first bit gets the role of the "sign" bit, as it can be used to distinguish between nonnegative and negative decimal values. If the most significant bit is 1, then the binary can be said to be negative, where as if the most significant bit (the leftmost) is 0, you can say the decimal value is nonnegative.
"Sign-magnitude" negative numbers just have the sign bit flipped of their positive counterparts, but this approach has to deal with interpreting 1000 (one 1 followed by all 0s) as "negative zero" which is confusing.
"Ones' complement" negative numbers are just the bit-complement of their positive counterparts, which also leads to a confusing "negative zero" with 1111 (all ones).
You will likely not have to deal with Ones' Complement or Sign-Magnitude integer representations unless you are working very close to the hardware.
I wonder if it could be explained any better than the Wikipedia article.
The basic problem that you are trying to solve with two's complement representation is the problem of storing negative integers.
First, consider an unsigned integer stored in 4 bits. You can have the following
0000 = 0
0001 = 1
0010 = 2
...
1111 = 15
These are unsigned because there is no indication of whether they are negative or positive.
Sign Magnitude and Excess Notation
To store negative numbers you can try a number of things. First, you can use sign magnitude notation which assigns the first bit as a sign bit to represent +/- and the remaining bits to represent the magnitude. So using 4 bits again and assuming that 1 means - and 0 means + then you have
0000 = +0
0001 = +1
0010 = +2
...
1000 = -0
1001 = -1
1111 = -7
So, you see the problem there? We have positive and negative 0. The bigger problem is adding and subtracting binary numbers. The circuits to add and subtract using sign magnitude will be very complex.
What is
0010
1001 +
----
?
Another system is excess notation. You can store negative numbers, you get rid of the two zeros problem but addition and subtraction remains difficult.
So along comes two's complement. Now you can store positive and negative integers and perform arithmetic with relative ease. There are a number of methods to convert a number into two's complement. Here's one.
Convert Decimal to Two's Complement
Convert the number to binary (ignore the sign for now)
e.g. 5 is 0101 and -5 is 0101
If the number is a positive number then you are done.
e.g. 5 is 0101 in binary using two's complement notation.
If the number is negative then
3.1 find the complement (invert 0's and 1's)
e.g. -5 is 0101 so finding the complement is 1010
3.2 Add 1 to the complement 1010 + 1 = 1011.
Therefore, -5 in two's complement is 1011.
So, what if you wanted to do 2 + (-3) in binary? 2 + (-3) is -1.
What would you have to do if you were using sign magnitude to add these numbers? 0010 + 1101 = ?
Using two's complement consider how easy it would be.
2 = 0010
-3 = 1101 +
-------------
-1 = 1111
Converting Two's Complement to Decimal
Converting 1111 to decimal:
The number starts with 1, so it's negative, so we find the complement of 1111, which is 0000.
Add 1 to 0000, and we obtain 0001.
Convert 0001 to decimal, which is 1.
Apply the sign = -1.
Tada!
Like most explanations I've seen, the ones above are clear about how to work with 2's complement, but don't really explain what they are mathematically. I'll try to do that, for integers at least, and I'll cover some background that's probably familiar first.
Recall how it works for decimal: 2345 is a way of writing 2 × 103 + 3 × 102 + 4 × 101 + 5 × 100.
In the same way, binary is a way of writing numbers using just 0 and 1 following the same general idea, but replacing those 10s above with 2s. Then in binary, 1111is a way of writing 1 × 23 + 1 × 22 + 1 × 21 + 1 × 20and if you work it out, that turns out to equal 15 (base 10). That's because it is 8+4+2+1 = 15.
This is all well and good for positive numbers. It even works for negative numbers if you're willing to just stick a minus sign in front of them, as humans do with decimal numbers. That can even be done in computers, sort of, but I haven't seen such a computer since the early 1970's. I'll leave the reasons for a different discussion.
For computers it turns out to be more efficient to use a complement representation for negative numbers. And here's something that is often overlooked. Complement notations involve some kind of reversal of the digits of the number, even the implied zeroes that come before a normal positive number. That's awkward, because the question arises: all of them? That could be an infinite number of digits to be considered.
Fortunately, computers don't represent infinities. Numbers are constrained to a particular length (or width, if you prefer). So let's return to positive binary numbers, but with a particular size. I'll use 8 digits ("bits") for these examples. So our binary number would really be 00001111or 0 × 27 + 0 × 26 + 0 × 25 + 0 × 24 + 1 × 23 + 1 × 22 + 1 × 21 + 1 × 20
To form the 2's complement negative, we first complement all the (binary) digits to form 11110000and add 1 to form 11110001but how are we to understand that to mean -15?
The answer is that we change the meaning of the high-order bit (the leftmost one). This bit will be a 1 for all negative numbers. The change will be to change the sign of its contribution to the value of the number it appears in. So now our 11110001 is understood to represent -1 × 27 + 1 × 26 + 1 × 25 + 1 × 24 + 0 × 23 + 0 × 22 + 0 × 21 + 1 × 20Notice that "-" in front of that expression? It means that the sign bit carries the weight -27, that is -128 (base 10). All the other positions retain the same weight they had in unsigned binary numbers.
Working out our -15, it is -128 + 64 + 32 + 16 + 1 Try it on your calculator. it's -15.
Of the three main ways that I've seen negative numbers represented in computers, 2's complement wins hands down for convenience in general use. It has an oddity, though. Since it's binary, there have to be an even number of possible bit combinations. Each positive number can be paired with its negative, but there's only one zero. Negating a zero gets you zero. So there's one more combination, the number with 1 in the sign bit and 0 everywhere else. The corresponding positive number would not fit in the number of bits being used.
What's even more odd about this number is that if you try to form its positive by complementing and adding one, you get the same negative number back. It seems natural that zero would do this, but this is unexpected and not at all the behavior we're used to because computers aside, we generally think of an unlimited supply of digits, not this fixed-length arithmetic.
This is like the tip of an iceberg of oddities. There's more lying in wait below the surface, but that's enough for this discussion. You could probably find more if you research "overflow" for fixed-point arithmetic. If you really want to get into it, you might also research "modular arithmetic".
2's complement is very useful for finding the value of a binary, however I thought of a much more concise way of solving such a problem(never seen anyone else publish it):
take a binary, for example: 1101 which is [assuming that space "1" is the sign] equal to -3.
using 2's complement we would do this...flip 1101 to 0010...add 0001 + 0010 ===> gives us 0011. 0011 in positive binary = 3. therefore 1101 = -3!
What I realized:
instead of all the flipping and adding, you can just do the basic method for solving for a positive binary(lets say 0101) is (23 * 0) + (22 * 1) + (21 * 0) + (20 * 1) = 5.
Do exactly the same concept with a negative!(with a small twist)
take 1101, for example:
for the first number instead of 23 * 1 = 8 , do -(23 * 1) = -8.
then continue as usual, doing -8 + (22 * 1) + (21 * 0) + (20 * 1) = -3
Imagine that you have a finite number of bits/trits/digits/whatever. You define 0 as all digits being 0, and count upwards naturally:
00
01
02
..
Eventually you will overflow.
98
99
00
We have two digits and can represent all numbers from 0 to 100. All those numbers are positive! Suppose we want to represent negative numbers too?
What we really have is a cycle. The number before 2 is 1. The number before 1 is 0. The number before 0 is... 99.
So, for simplicity, let's say that any number over 50 is negative. "0" through "49" represent 0 through 49. "99" is -1, "98" is -2, ... "50" is -50.
This representation is ten's complement. Computers typically use two's complement, which is the same except using bits instead of digits.
The nice thing about ten's complement is that addition just works. You do not need to do anything special to add positive and negative numbers!
I read a fantastic explanation on Reddit by jng, using the odometer as an analogy.
It is a useful convention. The same circuits and logic operations that
add / subtract positive numbers in binary still work on both positive
and negative numbers if using the convention, that's why it's so
useful and omnipresent.
Imagine the odometer of a car, it rolls around at (say) 99999. If you
increment 00000 you get 00001. If you decrement 00000, you get 99999
(due to the roll-around). If you add one back to 99999 it goes back to
00000. So it's useful to decide that 99999 represents -1. Likewise, it is very useful to decide that 99998 represents -2, and so on. You have
to stop somewhere, and also by convention, the top half of the numbers
are deemed to be negative (50000-99999), and the bottom half positive
just stand for themselves (00000-49999). As a result, the top digit
being 5-9 means the represented number is negative, and it being 0-4
means the represented is positive - exactly the same as the top bit
representing sign in a two's complement binary number.
Understanding this was hard for me too. Once I got it and went back to
re-read the books articles and explanations (there was no internet
back then), it turned out a lot of those describing it didn't really
understand it. I did write a book teaching assembly language after
that (which did sell quite well for 10 years).
Two complement is found out by adding one to 1'st complement of the given number.
Lets say we have to find out twos complement of 10101 then find its ones complement, that is, 01010 add 1 to this result, that is, 01010+1=01011, which is the final answer.
Lets get the answer 10 – 12 in binary form using 8 bits:
What we will really do is 10 + (-12)
We need to get the compliment part of 12 to subtract it from 10.
12 in binary is 00001100.
10 in binary is 00001010.
To get the compliment part of 12 we just reverse all the bits then add 1.
12 in binary reversed is 11110011. This is also the Inverse code (one's complement).
Now we need to add one, which is now 11110100.
So 11110100 is the compliment of 12! Easy when you think of it this way.
Now you can solve the above question of 10 - 12 in binary form.
00001010
11110100
-----------------
11111110
Looking at the two's complement system from a math point of view it really makes sense. In ten's complement, the idea is to essentially 'isolate' the difference.
Example: 63 - 24 = x
We add the complement of 24 which is really just (100 - 24). So really, all we are doing is adding 100 on both sides of the equation.
Now the equation is: 100 + 63 - 24 = x + 100, that is why we remove the 100 (or 10 or 1000 or whatever).
Due to the inconvenient situation of having to subtract one number from a long chain of zeroes, we use a 'diminished radix complement' system, in the decimal system, nine's complement.
When we are presented with a number subtracted from a big chain of nines, we just need to reverse the numbers.
Example: 99999 - 03275 = 96724
That is the reason, after nine's complement, we add 1. As you probably know from childhood math, 9 becomes 10 by 'stealing' 1. So basically it's just ten's complement that takes 1 from the difference.
In Binary, two's complement is equatable to ten's complement, while one's complement to nine's complement. The primary difference is that instead of trying to isolate the difference with powers of ten (adding 10, 100, etc. into the equation) we are trying to isolate the difference with powers of two.
It is for this reason that we invert the bits. Just like how our minuend is a chain of nines in decimal, our minuend is a chain of ones in binary.
Example: 111111 - 101001 = 010110
Because chains of ones are 1 below a nice power of two, they 'steal' 1 from the difference like nine's do in decimal.
When we are using negative binary number's, we are really just saying:
0000 - 0101 = x
1111 - 0101 = 1010
1111 + 0000 - 0101 = x + 1111
In order to 'isolate' x, we need to add 1 because 1111 is one away from 10000 and we remove the leading 1 because we just added it to the original difference.
1111 + 1 + 0000 - 0101 = x + 1111 + 1
10000 + 0000 - 0101 = x + 10000
Just remove 10000 from both sides to get x, it's basic algebra.
The word complement derives from completeness. In the decimal world the numerals 0 through 9 provide a complement (complete set) of numerals or numeric symbols to express all decimal numbers. In the binary world the numerals 0 and 1 provide a complement of numerals to express all binary numbers. In fact The symbols 0 and 1 must be used to represent everything (text, images, etc) as well as positive (0) and negative (1).
In our world the blank space to the left of number is considered as zero:
35=035=000000035.
In a computer storage location there is no blank space. All bits (binary digits) must be either 0 or 1. To efficiently use memory numbers may be stored as 8 bit, 16 bit, 32 bit, 64 bit, 128 bit representations. When a number that is stored as an 8 bit number is transferred to a 16 bit location the sign and magnitude (absolute value) must remain the same. Both 1's complement and 2's complement representations facilitate this.
As a noun:
Both 1's complement and 2's complement are binary representations of signed quantities where the most significant bit (the one on the left) is the sign bit. 0 is for positive and 1 is for negative.
2s complement does not mean negative. It means a signed quantity. As in decimal the magnitude is represented as the positive quantity. The structure uses sign extension to preserve the quantity when promoting to a register [] with more bits:
[0101]=[00101]=[00000000000101]=5 (base 10)
[1011]=[11011]=[11111111111011]=-5(base 10)
As a verb:
2's complement means to negate. It does not mean make negative. It means if negative make positive; if positive make negative. The magnitude is the absolute value:
if a >= 0 then |a| = a
if a < 0 then |a| = -a = 2scomplement of a
This ability allows efficient binary subtraction using negate then add.
a - b = a + (-b)
The official way to take the 1's complement is for each digit subtract its value from 1.
1'scomp(0101) = 1010.
This is the same as flipping or inverting each bit individually. This results in a negative zero which is not well loved so adding one to te 1's complement gets rid of the problem.
To negate or take the 2s complement first take the 1s complement then add 1.
Example 1 Example 2
0101 --original number 1101
1's comp 1010 0010
add 1 0001 0001
2's comp 1011 --negated number 0011
In the examples the negation works as well with sign extended numbers.
Adding:
1110 Carry 111110 Carry
0110 is the same as 000110
1111 111111
sum 0101 sum 000101
SUbtracting:
1110 Carry 00000 Carry
0110 is the same as 00110
-0111 +11001
---------- ----------
sum 0101 sum 11111
Notice that when working with 2's complement, blank space to the left of the number is filled with zeros for positive numbers butis filled with ones for negative numbers. The carry is always added and must be either a 1 or 0.
Cheers
2's complement is essentially a way of coming up with the additive inverse of a binary number. Ask yourself this: Given a number in binary form (present at a fixed length memory location), what bit pattern, when added to the original number (at the fixed length memory location), would make the result all zeros ? (at the same fixed length memory location). If we could come up with this bit pattern then that bit pattern would be the -ve representation (additive inverse) of the original number; as by definition adding a number to its additive inverse always results in zero. Example: take 5 which is 101 present inside a single 8 bit byte. Now the task is to come up with a bit pattern which when added to the given bit pattern (00000101) would result in all zeros at the memory location which is used to hold this 5 i.e. all 8 bits of the byte should be zero. To do that, start from the right most bit of 101 and for each individual bit, again ask the same question: What bit should I add to the current bit to make the result zero ? continue doing that taking in account the usual carry over. After we are done with the 3 right most places (the digits that define the original number without regard to the leading zeros) the last carry goes in the bit pattern of the additive inverse. Furthermore, since we are holding in the original number in a single 8 bit byte, all other leading bits in the additive inverse should also be 1's so that (and this is important) when the computer adds "the number" (represented using the 8 bit pattern) and its additive inverse using "that" storage type (a byte) the result in that byte would be all zeros.
1 1 1
----------
1 0 1
1 0 1 1 ---> additive inverse
---------
0 0 0
Many of the answers so far nicely explain why two's complement is used to represent negative numbers, but do not tell us what two's complement number is, particularly not why a '1' is added, and in fact often added in a wrong way.
The confusion comes from a poor understanding of the definition of a complement number. A complement is the missing part that would make something complete.
The radix complement of an n digit number x in radix b is, by definition, b^n-x.
In binary 4 is represented by 100, which has 3 digits (n=3) and a radix of 2 (b=2). So its radix complement is b^n-x = 2^3-4=8-4=4 (or 100 in binary).
However, in binary obtaining a radix's complement is not as easy as getting its diminished radix complement, which is defined as (b^n-1)-y, just 1 less than that of radix complement. To get a diminished radix complement, you simply flip all the digits.
100 -> 011 (diminished (one's) radix complement)
to obtain the radix (two's) complement, we simply add 1, as the definition defined.
011 +1 ->100 (two's complement).
Now with this new understanding, let's take a look of the example given by Vincent Ramdhanie (see above second response):
Converting 1111 to decimal:
The number starts with 1, so it's negative, so we find the complement of 1111, which is 0000.
Add 1 to 0000, and we obtain 0001.
Convert 0001 to decimal, which is 1.
Apply the sign = -1.
Tada!
Should be understood as:
The number starts with 1, so it's negative. So we know it is a two's complement of some value x. To find the x represented by its two's complement, we first need find its 1's complement.
two's complement of x: 1111
one's complement of x: 1111-1 ->1110;
x = 0001, (flip all digits)
Apply the sign -, and the answer =-x =-1.
I liked lavinio's answer, but shifting bits adds some complexity. Often there's a choice of moving bits while respecting the sign bit or while not respecting the sign bit. This is the choice between treating the numbers as signed (-8 to 7 for a nibble, -128 to 127 for bytes) or full-range unsigned numbers (0 to 15 for nibbles, 0 to 255 for bytes).
It is a clever means of encoding negative integers in such a way that approximately half of the combination of bits of a data type are reserved for negative integers, and the addition of most of the negative integers with their corresponding positive integers results in a carry overflow that leaves the result to be binary zero.
So, in 2's complement if one is 0x0001 then -1 is 0x1111, because that will result in a combined sum of 0x0000 (with an overflow of 1).
2’s Complements: When we add an extra one with the 1’s complements of a number we will get the 2’s complements. For example: 100101 it’s 1’s complement is 011010 and 2’s complement is 011010+1 = 011011 (By adding one with 1's complement) For more information
this article explain it graphically.
Two's complement is mainly used for the following reasons:
To avoid multiple representations of 0
To avoid keeping track of carry bit (as in one's complement) in case of an overflow.
Carrying out simple operations like addition and subtraction becomes easy.
Two's complement is one of the ways of expressing a negative number and most of the controllers and processors store a negative number in two's complement form.
In simple terms, two's complement is a way to store negative numbers in computer memory. Whereas positive numbers are stored as a normal binary number.
Let's consider this example,
The computer uses the binary number system to represent any number.
x = 5;
This is represented as 0101.
x = -5;
When the computer encounters the - sign, it computes its two's complement and stores it.
That is, 5 = 0101 and its two's complement is 1011.
The important rules the computer uses to process numbers are,
If the first bit is 1 then it must be a negative number.
If all the bits except first bit are 0 then it is a positive number, because there is no -0 in number system (1000 is not -0 instead it is positive 8).
If all the bits are 0 then it is 0.
Else it is a positive number.
To bitwise complement a number is to flip all the bits in it. To two’s complement it, we flip all the bits and add one.
Using 2’s complement representation for signed integers, we apply the 2’s complement operation to convert a positive number to its negative equivalent and vice versa. So using nibbles for an example, 0001 (1) becomes 1111 (-1) and applying the op again, returns to 0001.
The behaviour of the operation at zero is advantageous in giving a single representation for zero without special handling of positive and negative zeroes. 0000 complements to 1111, which when 1 is added. overflows to 0000, giving us one zero, rather than a positive and a negative one.
A key advantage of this representation is that the standard addition circuits for unsigned integers produce correct results when applied to them. For example adding 1 and -1 in nibbles: 0001 + 1111, the bits overflow out of the register, leaving behind 0000.
For a gentle introduction, the wonderful Computerphile have produced a video on the subject.
The question is 'What is “two's complement”?'
The simple answer for those wanting to understand it theoretically (and me seeking to complement the other more practical answers): 2's complement is the representation for negative integers in the dual system that does not require additional characters, such as + and -.
Two's complement of a given number is the number got by adding 1 with the ones' complement of the number.
Suppose, we have a binary number: 10111001101
Its 1's complement is: 01000110010
And its two's complement will be: 01000110011
Reference: Two's Complement (Thomas Finley)
I invert all the bits and add 1. Programmatically:
// In C++11
int _powers[] = {
1,
2,
4,
8,
16,
32,
64,
128
};
int value = 3;
int n_bits = 4;
int twos_complement = (value ^ ( _powers[n_bits]-1)) + 1;
You can also use an online calculator to calculate the two's complement binary representation of a decimal number: http://www.convertforfree.com/twos-complement-calculator/
The simplest answer:
1111 + 1 = (1)0000. So 1111 must be -1. Then -1 + 1 = 0.
It's perfect to understand these all for me.
I'm trying to wrap my head around overflow within twos complement for example say I'm trying to take away these two binary numbers:
1111 1000 0100 - 010 111 001 000
I convert the 2nd binary number to it's two complement equivalent and then simply add it but I noticed it resulted in an overflow of 1, do I simply ignore the overflow? or is there a rule I must follow
1111 1000 0100 + 1010 0011 1000 = (1) 1001 1011 1100
Short answer:
if you are performing arithmetic on fixed-width binary numbers, using two's complement representation for negative numbers, then yes, you ignore the one-bit overflow.
Long Answer:
You can consider each ith bit in n-bit two's complement notation have place value 2^i, for 0 <= i < n - 1, with bit n - 1 (the sign bit) having place value -2^(n - 1). That's a negative place value for the sign bit. If you compute the sum of two such numbers as if they were unsigned n-bit binary numbers, these cases are fine:
the sign bit is not set in the either addend or in the result (reinterpreted as being in two's-complement representation),
the sign bit is set in exactly one of the addends, regardless of overflow (which is ignored if it occurs), or
the sign bit is set in both addends (therefore there is an overflow, which is ignored) and in the result.
To understand that, it may be easier to think about the problem as two separate sums: a sum of the sign bits, and a sum of the value (other) bits. An overflow of the value sum yields an overflow bit whose place value is 2^(n-1) -- exactly the inverse of the place value of a sign bit -- therefore such an overflow cancels one sign bit.
The negative + negative case requires such a cancellation for the result to be representable (two sign bits + one value overflow = one sign bit), and the positive + positive case cannot accommodate such a cancellation because there is no sign bit available to be cancelled. In the positive + negative case, there is an overflow of the value-bit sum in exactly those cases where the result is non-negative; you can consider that to cancel the sign bit of the negative addend, wich yields the same result as ignoring the overflow of the overall unsigned sum, and reinterpreting the sum as a two's complement number.
The remaining cases yield mathematical results that cannot be represented in n-bit two's complement format -- either greater than the largest representable number, or less than the smallest. If you ignore overflow then such results can be recognized by an apparent sign flip. What you do with that is a question of error recovery strategy.
From Wikipedia's article on 2's complement in the section on addition at https://en.wikipedia.org/wiki/Two%27s_complement#Addition, my understanding is that carry beyond the given (fixed) bit length (to the left) can be ignored but not overflow as determined when the leftmost two bits of the carry are different. The article shows how to maintain a carry row so as to tell if there was overflow and here is a simple example in the same style:
In 4 bit 2's complement -2 is 1110 and +3 is 0011 so
11110 carry
1110 -2
+0011 +3
----
10001 which is 0001 or simply 1 ignoring the carry in bit 5 and is
safe since the leftmost two bits in the carry row are identical
Although this is a very old question, it comes up frequently. In two's complement addition, a carry out from the leftmost digit is discarded. Why? Although not precisely correct mathematically, it is easiest to think of a two’s complement number as having a sign bit on the left and value bits elsewhere. The only way a carry out of the sign bit can occur is if the sign bits of both addends were one (negative) and there was a carry in to the sign bit. In that case, the sign bit of the result will be one, which is correct. A problem occurs if the carry in to the sign bit is different from the carry out. That causes an incorrect sign bit, which is an overflow condition. That can be detected without referring to the carry out from the sign bit because the sign of the result will be wrong. For example, if two positive numbers are added and the result is negative, something is wrong. The something that’s wrong is that the sum of the value bits has overflowed into the sign bit and the result is in error.
With pen and paper arithmetic, it is usual to discard the carry and check that the sign of the result is correct. In electronic circuits, the easiest way is to compare that carry in to the carry out with an XOR and signal an error if they differ. The carry out is not otherwise used or stored.
I attempted to multiply binary 1111 as first input and 1111 as second input. When I multiply as usual I came across having to do the addition below I encounter having to carry the 1 with the three 1's which would mean 4 in binary with 2 bits. But that's impossible to represent 4 in 2 bits for this multiplication problem.
If you want to add multiple binary values, then you just carry whatever is left over after adding a column, regardless of how many bits you need to represent the carry.
It's just like doing the decimal add 99+99+99+99+99+99+99+99+99+99+99+99, when adding the least significant column, you end up with 108, so you carry 10 eventhough it's too large to fit in a single digit.
Likewise, if you add the binary 11+11+11+11+11 you end up with 101 when adding the least significant column, so you carry 10.
However, normally you only add two binary numbers at a time, as that lets you get away with using a single bit for carry.
What you have to do is carry the numbers over another digit.
Take the scenario:
11
+11
+11
you would have 1001 as your answer because 4 in binary is 100. Simply carry over the 1s into the correct place.
This is a super naive question (I know), but I think that it will make for a good jumping off point into considering how the basic instruction set of a CPU actually gets carried out:
In a two's complement system, you cannot invert the sign of the most negative number that your implementation can represent. The theoretical reason for this is obvious in that the negation of the most negative number would be out of the range of the implementation (the range is always something like
-128 to 127).
However, what actually happens when you try to carry out the negation operation on the most negative number is pretty strange. For example, in an 8 bit representation, the most negative number is -128, or 1000 0000 in binary. Normally, to negate a number you would flip all the bits and then add one. However, if you try to do this with -128 you end up with:
1000 0000 ->
0111 1111 ->
1000 0000
the same number that you started out with. For this reason, wikipedia calls it "the weird number".
In that same wikipedia article, it says that the above negation
is detected as an overflow condition since there was a carry into but not out of the most-significant bit.
So my question is this:
A) What the heck does that mean? and
B) It seems like the CPU would need to perform an extra error checking step each and every time it carried out a basic arithmetic operation in order to avoid accidents relating to this negation, creating significant overhead. If that is the case, why not just truncate the range of numbers that can be represented to leave the weird number out (i.e. -127 to 127 for 8 bits)? If that isn't the case, how can you implement such error checking without creating extra overhead?
The carry-out bit from the MSB is used as a flag to indicate that we
need more bits. Without it, we would have a system of modular
arithmetic1 without any way of detecting when we wrap around.
In modular arithmetic, you don’t deal with numbers but with
equivalence classes of numbers that have the same remainder. In such
a system, after adding 1 to 127, you would get −128, and you would
conclude that +128 and −128 belong to the same equivalence class.
If you restricted yourself to numbers in the range −127 to +127, you
would have to redefine addition, since 127 + 1 = −127 is nonsense.
Two’s-complement arithmetic, when presented to you by a computer, is
essentially modular arithmetic with the ability to detect an overflow.
This is what a 4-bit adder would look like when adding 0001 to
0111. You can see that in the MSB the carry-in and carry-out are
different:
0 0 0 1
| 0 | 1 | 1 | 1
| | | | | | | |
v v v v v v v v
0 <- ADD <-1- ADD <-1- ADD <-1- ADD <- 0
^ | ^ | | |
v v v v
1 0 0 0
It is this flag that the ALU uses to signal that an overflow occurred,
without any extra steps.
1. Modular arithmetic goes from 0 to 255 instead of −127 to 128, but the basic idea is the same.
It's not that the CPU does another check, its that the transistors are arranged to notice when this happens. And they are built that way because the engineers picked two-complement before they started designing the thing.
The result is that it happens during the same clock cycle as a non-overflowing result would be returned.
How does it work?
The "add 1" stage implements a cascade logic: starting with the LSB each bit is subjected in turn to the truth table
old-bit carry-in new-bit carry-out
-------------------------------------
0 0 0 0
0 1 1 0
1 0 1 0
1 1 0 1
(that is new-bit = old-bit xor carry-in and carry-out = old-bit and carry-in). The "carry-in" for the LSB is the 1 that we're adding, and for the rest of the bits it is the "carry-out" of the previous one (which is why this has to be done in a cascade).
The last of these circuits just adds a circuit for signed-overflow = (carry-in and not carry-out).
First off the wikipedia article states it cannot be negated from a negative signed number to a signed number. And what they mean is because it takes 9 bits to represent positive 128, which you cannot do with an 8 bit register. If you are going from negative signed to positive unsigned as a conversion, then you have enough bits. And the hardware should give you 0x80 when you negate 0x80 because that is the right answer.
For add, subtract, multiply, etc addition in twos complement is no different than decimal math from elementary school. You line up your binary numbers, add the columns, the result for that column is the least significant digit and the rest is carried over to the next column. So adding a 0b001 to 0b001 for example
1
001
001
===
010
Add the two ones in the rightmost column, the result is 0b10 (2 decimal), write zero then carry the one, one plus zero plus zero is one, nothing to carry, zero plus zero is zero, the result is 0b010.
The right most column where 1 plus 1 is 0b10 and we write 0 carry the one, well that carry the one is at the same time the carry out of the right most column and is the carry in of the second column. Also, with pencil and paper math we normally only talk about carry of something when it is non-zero but if you think about it you are always carrying a number like our second columns one plus zero is one carry the zero.
You can think of a twos complement negate as invert and add one, or walking the bits and inverting up to a point then not inverting, or taking the result of zero minus the number.
You can work subtract in binary using pencil and paper for what it is worth, makes your head hurt when borrowing compared to decimal, but works. For what you are asking though think of invert and add one.
It is easier to wrap your head around this if you take it down to even fewer bits than 8, three is a manageable number, it all scales from there.
So the first column below is the input, the second column is the inverted version and the third column is the second column plus one. The fourth column is the carry in to the msbit, the fifth column is the carry out of the msbit.
000 111 000 1 1
001 110 111 0 0
010 101 110 0 0
011 100 101 0 0
100 011 100 1 0
101 010 011 0 0
110 001 010 0 0
111 000 001 0 0
Real quick look at at adding a one to two bits:
00+1 = 001
01+1 = 010
10+1 = 011
11+1 = 100
For the case of adding one to a number, the only case where you carry out from the second bit into the third bit is when your bits are all ones, a single zero in there stops the cascading carry bits. So in the three bit inversion table above the only two cases where you have a carry into the msbit is 111 and 011 because those are the only two cases where those lower bits are all set. For the 111 case the msbit has a carry in and a carry out. for the 011 case the msbit has a carry in but not a carry out.
So as stated by someone else there are transistors wired up in the chip, if msbit carry in is set and msbit carry out is not set then set some flag somewhere, otherwise clear the flag.
So note that the three bit examples above scale. if after you invert and before you add one you have 0b01111111 then you are going to get a carry in without the carry out. If you have 0b11111111 then you get a carry in and a carry out. Note that zero is also a number where you get the same number back when you invert it, the difference is that when the bits are considered as signed, zero can be represented when negated, 1 with all zeros cannot.
The bottom line though is that this is not a crisis or end of the world thing there is a whole lot of math and other operations in the processor where carry bits and significant bits are falling off one side or the other and overflows and underflows are firing off, etc. Most of the time the programmers never check for such conditions and those bits just fall on the floor, sometimes causing the program to crash or sometimes the programmer has used 16 bit numbers for 8 bit math just to make sure nothing bad happens, or uses 8 bit numbers for 5 bit math for the same reason.
Note that the hardware doesnt know signed or unsigned for addition and subtraction. also the hardware doesnt know how to subtract. Hardware adders are three bit adders (two operands and carry in) with a result and carry out. Wire 8 of these up you have an 8 bit adder or subtractor, add without carry is the two operands wired directly with a zero wired in as the lsbit carry in. Add with carry is the two operands wired directly with the carry bit wired to the lsbit carry in. Subtract is add with the second operand inverted and a one on the carry in bit. At least from a high level perspective, that logic can all get optimized and implemented in ways often two hard to understand on casual inspection.
The really fun exercise is multiply, think about doing binary multiplication with pencil and paper, then realize it is much easier than decimal, because it is just a series of shifts and adds. given enough gates you can represent each result bit as a equation with the inputs to the equation being the operands. meaning you can do a single clock multiply if you wish, in the early days that was too many gates, so multi clock shift and adds were done, today we burn the gates and get single clock multiplies. Also note that understanding this also means that if you do say a 16 bit = 8 bit times 8 bit multiply, the lower 8 bit result is the same whether it is a signed multiply or unsigned. Since most folks do things like int = int * int; you really dont need a signed or unsigned multiply if all you care about is the result bits (no checking of flags, etc). fun stuff..
In the ARM Architecture Manual (DDI100E):
OverflowFrom
Returns 1 if the addition or subtraction specified as its parameter
caused a 32-bit signed overflow. [...]
Subtraction causes an overflow if the operands have different signs,
and the first operand and the result have different signs.
NEG
[...]
V Flag = OverflowFrom(0 - Rm)
NEG is the instruction for computing the negation of a number, i.e. the twos complement.
The V flag signals signed overflow and can be used for conditional branching. It's fairly standard across different processor architectures, together with the three other flags Z (zero), C (carry) and N (negative).
For 0 - (-128) = 0 + 128 = -128 the first operand is 0 and the second operand as well as the result is -128, so the condition for overflow is satisfied, and the V flag is set.
I'm in a computer systems course and have been struggling, in part, with two's complement. I want to understand it, but everything I've read hasn't brought the picture together for me. I've read the Wikipedia article and various other articles, including my text book.
What is two's complement, how can we use it and how can it affect numbers during operations like casts (from signed to unsigned and vice versa), bit-wise operations and bit-shift operations?
Two's complement is a clever way of storing integers so that common math problems are very simple to implement.
To understand, you have to think of the numbers in binary.
It basically says,
for zero, use all 0's.
for positive integers, start counting up, with a maximum of 2(number of bits - 1)-1.
for negative integers, do exactly the same thing, but switch the role of 0's and 1's and count down (so instead of starting with 0000, start with 1111 - that's the "complement" part).
Let's try it with a mini-byte of 4 bits (we'll call it a nibble - 1/2 a byte).
0000 - zero
0001 - one
0010 - two
0011 - three
0100 to 0111 - four to seven
That's as far as we can go in positives. 23-1 = 7.
For negatives:
1111 - negative one
1110 - negative two
1101 - negative three
1100 to 1000 - negative four to negative eight
Note that you get one extra value for negatives (1000 = -8) that you don't for positives. This is because 0000 is used for zero. This can be considered as Number Line of computers.
Distinguishing between positive and negative numbers
Doing this, the first bit gets the role of the "sign" bit, as it can be used to distinguish between nonnegative and negative decimal values. If the most significant bit is 1, then the binary can be said to be negative, where as if the most significant bit (the leftmost) is 0, you can say the decimal value is nonnegative.
"Sign-magnitude" negative numbers just have the sign bit flipped of their positive counterparts, but this approach has to deal with interpreting 1000 (one 1 followed by all 0s) as "negative zero" which is confusing.
"Ones' complement" negative numbers are just the bit-complement of their positive counterparts, which also leads to a confusing "negative zero" with 1111 (all ones).
You will likely not have to deal with Ones' Complement or Sign-Magnitude integer representations unless you are working very close to the hardware.
I wonder if it could be explained any better than the Wikipedia article.
The basic problem that you are trying to solve with two's complement representation is the problem of storing negative integers.
First, consider an unsigned integer stored in 4 bits. You can have the following
0000 = 0
0001 = 1
0010 = 2
...
1111 = 15
These are unsigned because there is no indication of whether they are negative or positive.
Sign Magnitude and Excess Notation
To store negative numbers you can try a number of things. First, you can use sign magnitude notation which assigns the first bit as a sign bit to represent +/- and the remaining bits to represent the magnitude. So using 4 bits again and assuming that 1 means - and 0 means + then you have
0000 = +0
0001 = +1
0010 = +2
...
1000 = -0
1001 = -1
1111 = -7
So, you see the problem there? We have positive and negative 0. The bigger problem is adding and subtracting binary numbers. The circuits to add and subtract using sign magnitude will be very complex.
What is
0010
1001 +
----
?
Another system is excess notation. You can store negative numbers, you get rid of the two zeros problem but addition and subtraction remains difficult.
So along comes two's complement. Now you can store positive and negative integers and perform arithmetic with relative ease. There are a number of methods to convert a number into two's complement. Here's one.
Convert Decimal to Two's Complement
Convert the number to binary (ignore the sign for now)
e.g. 5 is 0101 and -5 is 0101
If the number is a positive number then you are done.
e.g. 5 is 0101 in binary using two's complement notation.
If the number is negative then
3.1 find the complement (invert 0's and 1's)
e.g. -5 is 0101 so finding the complement is 1010
3.2 Add 1 to the complement 1010 + 1 = 1011.
Therefore, -5 in two's complement is 1011.
So, what if you wanted to do 2 + (-3) in binary? 2 + (-3) is -1.
What would you have to do if you were using sign magnitude to add these numbers? 0010 + 1101 = ?
Using two's complement consider how easy it would be.
2 = 0010
-3 = 1101 +
-------------
-1 = 1111
Converting Two's Complement to Decimal
Converting 1111 to decimal:
The number starts with 1, so it's negative, so we find the complement of 1111, which is 0000.
Add 1 to 0000, and we obtain 0001.
Convert 0001 to decimal, which is 1.
Apply the sign = -1.
Tada!
Like most explanations I've seen, the ones above are clear about how to work with 2's complement, but don't really explain what they are mathematically. I'll try to do that, for integers at least, and I'll cover some background that's probably familiar first.
Recall how it works for decimal: 2345 is a way of writing 2 × 103 + 3 × 102 + 4 × 101 + 5 × 100.
In the same way, binary is a way of writing numbers using just 0 and 1 following the same general idea, but replacing those 10s above with 2s. Then in binary, 1111is a way of writing 1 × 23 + 1 × 22 + 1 × 21 + 1 × 20and if you work it out, that turns out to equal 15 (base 10). That's because it is 8+4+2+1 = 15.
This is all well and good for positive numbers. It even works for negative numbers if you're willing to just stick a minus sign in front of them, as humans do with decimal numbers. That can even be done in computers, sort of, but I haven't seen such a computer since the early 1970's. I'll leave the reasons for a different discussion.
For computers it turns out to be more efficient to use a complement representation for negative numbers. And here's something that is often overlooked. Complement notations involve some kind of reversal of the digits of the number, even the implied zeroes that come before a normal positive number. That's awkward, because the question arises: all of them? That could be an infinite number of digits to be considered.
Fortunately, computers don't represent infinities. Numbers are constrained to a particular length (or width, if you prefer). So let's return to positive binary numbers, but with a particular size. I'll use 8 digits ("bits") for these examples. So our binary number would really be 00001111or 0 × 27 + 0 × 26 + 0 × 25 + 0 × 24 + 1 × 23 + 1 × 22 + 1 × 21 + 1 × 20
To form the 2's complement negative, we first complement all the (binary) digits to form 11110000and add 1 to form 11110001but how are we to understand that to mean -15?
The answer is that we change the meaning of the high-order bit (the leftmost one). This bit will be a 1 for all negative numbers. The change will be to change the sign of its contribution to the value of the number it appears in. So now our 11110001 is understood to represent -1 × 27 + 1 × 26 + 1 × 25 + 1 × 24 + 0 × 23 + 0 × 22 + 0 × 21 + 1 × 20Notice that "-" in front of that expression? It means that the sign bit carries the weight -27, that is -128 (base 10). All the other positions retain the same weight they had in unsigned binary numbers.
Working out our -15, it is -128 + 64 + 32 + 16 + 1 Try it on your calculator. it's -15.
Of the three main ways that I've seen negative numbers represented in computers, 2's complement wins hands down for convenience in general use. It has an oddity, though. Since it's binary, there have to be an even number of possible bit combinations. Each positive number can be paired with its negative, but there's only one zero. Negating a zero gets you zero. So there's one more combination, the number with 1 in the sign bit and 0 everywhere else. The corresponding positive number would not fit in the number of bits being used.
What's even more odd about this number is that if you try to form its positive by complementing and adding one, you get the same negative number back. It seems natural that zero would do this, but this is unexpected and not at all the behavior we're used to because computers aside, we generally think of an unlimited supply of digits, not this fixed-length arithmetic.
This is like the tip of an iceberg of oddities. There's more lying in wait below the surface, but that's enough for this discussion. You could probably find more if you research "overflow" for fixed-point arithmetic. If you really want to get into it, you might also research "modular arithmetic".
2's complement is very useful for finding the value of a binary, however I thought of a much more concise way of solving such a problem(never seen anyone else publish it):
take a binary, for example: 1101 which is [assuming that space "1" is the sign] equal to -3.
using 2's complement we would do this...flip 1101 to 0010...add 0001 + 0010 ===> gives us 0011. 0011 in positive binary = 3. therefore 1101 = -3!
What I realized:
instead of all the flipping and adding, you can just do the basic method for solving for a positive binary(lets say 0101) is (23 * 0) + (22 * 1) + (21 * 0) + (20 * 1) = 5.
Do exactly the same concept with a negative!(with a small twist)
take 1101, for example:
for the first number instead of 23 * 1 = 8 , do -(23 * 1) = -8.
then continue as usual, doing -8 + (22 * 1) + (21 * 0) + (20 * 1) = -3
Imagine that you have a finite number of bits/trits/digits/whatever. You define 0 as all digits being 0, and count upwards naturally:
00
01
02
..
Eventually you will overflow.
98
99
00
We have two digits and can represent all numbers from 0 to 100. All those numbers are positive! Suppose we want to represent negative numbers too?
What we really have is a cycle. The number before 2 is 1. The number before 1 is 0. The number before 0 is... 99.
So, for simplicity, let's say that any number over 50 is negative. "0" through "49" represent 0 through 49. "99" is -1, "98" is -2, ... "50" is -50.
This representation is ten's complement. Computers typically use two's complement, which is the same except using bits instead of digits.
The nice thing about ten's complement is that addition just works. You do not need to do anything special to add positive and negative numbers!
I read a fantastic explanation on Reddit by jng, using the odometer as an analogy.
It is a useful convention. The same circuits and logic operations that
add / subtract positive numbers in binary still work on both positive
and negative numbers if using the convention, that's why it's so
useful and omnipresent.
Imagine the odometer of a car, it rolls around at (say) 99999. If you
increment 00000 you get 00001. If you decrement 00000, you get 99999
(due to the roll-around). If you add one back to 99999 it goes back to
00000. So it's useful to decide that 99999 represents -1. Likewise, it is very useful to decide that 99998 represents -2, and so on. You have
to stop somewhere, and also by convention, the top half of the numbers
are deemed to be negative (50000-99999), and the bottom half positive
just stand for themselves (00000-49999). As a result, the top digit
being 5-9 means the represented number is negative, and it being 0-4
means the represented is positive - exactly the same as the top bit
representing sign in a two's complement binary number.
Understanding this was hard for me too. Once I got it and went back to
re-read the books articles and explanations (there was no internet
back then), it turned out a lot of those describing it didn't really
understand it. I did write a book teaching assembly language after
that (which did sell quite well for 10 years).
Two complement is found out by adding one to 1'st complement of the given number.
Lets say we have to find out twos complement of 10101 then find its ones complement, that is, 01010 add 1 to this result, that is, 01010+1=01011, which is the final answer.
Lets get the answer 10 – 12 in binary form using 8 bits:
What we will really do is 10 + (-12)
We need to get the compliment part of 12 to subtract it from 10.
12 in binary is 00001100.
10 in binary is 00001010.
To get the compliment part of 12 we just reverse all the bits then add 1.
12 in binary reversed is 11110011. This is also the Inverse code (one's complement).
Now we need to add one, which is now 11110100.
So 11110100 is the compliment of 12! Easy when you think of it this way.
Now you can solve the above question of 10 - 12 in binary form.
00001010
11110100
-----------------
11111110
Looking at the two's complement system from a math point of view it really makes sense. In ten's complement, the idea is to essentially 'isolate' the difference.
Example: 63 - 24 = x
We add the complement of 24 which is really just (100 - 24). So really, all we are doing is adding 100 on both sides of the equation.
Now the equation is: 100 + 63 - 24 = x + 100, that is why we remove the 100 (or 10 or 1000 or whatever).
Due to the inconvenient situation of having to subtract one number from a long chain of zeroes, we use a 'diminished radix complement' system, in the decimal system, nine's complement.
When we are presented with a number subtracted from a big chain of nines, we just need to reverse the numbers.
Example: 99999 - 03275 = 96724
That is the reason, after nine's complement, we add 1. As you probably know from childhood math, 9 becomes 10 by 'stealing' 1. So basically it's just ten's complement that takes 1 from the difference.
In Binary, two's complement is equatable to ten's complement, while one's complement to nine's complement. The primary difference is that instead of trying to isolate the difference with powers of ten (adding 10, 100, etc. into the equation) we are trying to isolate the difference with powers of two.
It is for this reason that we invert the bits. Just like how our minuend is a chain of nines in decimal, our minuend is a chain of ones in binary.
Example: 111111 - 101001 = 010110
Because chains of ones are 1 below a nice power of two, they 'steal' 1 from the difference like nine's do in decimal.
When we are using negative binary number's, we are really just saying:
0000 - 0101 = x
1111 - 0101 = 1010
1111 + 0000 - 0101 = x + 1111
In order to 'isolate' x, we need to add 1 because 1111 is one away from 10000 and we remove the leading 1 because we just added it to the original difference.
1111 + 1 + 0000 - 0101 = x + 1111 + 1
10000 + 0000 - 0101 = x + 10000
Just remove 10000 from both sides to get x, it's basic algebra.
The word complement derives from completeness. In the decimal world the numerals 0 through 9 provide a complement (complete set) of numerals or numeric symbols to express all decimal numbers. In the binary world the numerals 0 and 1 provide a complement of numerals to express all binary numbers. In fact The symbols 0 and 1 must be used to represent everything (text, images, etc) as well as positive (0) and negative (1).
In our world the blank space to the left of number is considered as zero:
35=035=000000035.
In a computer storage location there is no blank space. All bits (binary digits) must be either 0 or 1. To efficiently use memory numbers may be stored as 8 bit, 16 bit, 32 bit, 64 bit, 128 bit representations. When a number that is stored as an 8 bit number is transferred to a 16 bit location the sign and magnitude (absolute value) must remain the same. Both 1's complement and 2's complement representations facilitate this.
As a noun:
Both 1's complement and 2's complement are binary representations of signed quantities where the most significant bit (the one on the left) is the sign bit. 0 is for positive and 1 is for negative.
2s complement does not mean negative. It means a signed quantity. As in decimal the magnitude is represented as the positive quantity. The structure uses sign extension to preserve the quantity when promoting to a register [] with more bits:
[0101]=[00101]=[00000000000101]=5 (base 10)
[1011]=[11011]=[11111111111011]=-5(base 10)
As a verb:
2's complement means to negate. It does not mean make negative. It means if negative make positive; if positive make negative. The magnitude is the absolute value:
if a >= 0 then |a| = a
if a < 0 then |a| = -a = 2scomplement of a
This ability allows efficient binary subtraction using negate then add.
a - b = a + (-b)
The official way to take the 1's complement is for each digit subtract its value from 1.
1'scomp(0101) = 1010.
This is the same as flipping or inverting each bit individually. This results in a negative zero which is not well loved so adding one to te 1's complement gets rid of the problem.
To negate or take the 2s complement first take the 1s complement then add 1.
Example 1 Example 2
0101 --original number 1101
1's comp 1010 0010
add 1 0001 0001
2's comp 1011 --negated number 0011
In the examples the negation works as well with sign extended numbers.
Adding:
1110 Carry 111110 Carry
0110 is the same as 000110
1111 111111
sum 0101 sum 000101
SUbtracting:
1110 Carry 00000 Carry
0110 is the same as 00110
-0111 +11001
---------- ----------
sum 0101 sum 11111
Notice that when working with 2's complement, blank space to the left of the number is filled with zeros for positive numbers butis filled with ones for negative numbers. The carry is always added and must be either a 1 or 0.
Cheers
2's complement is essentially a way of coming up with the additive inverse of a binary number. Ask yourself this: Given a number in binary form (present at a fixed length memory location), what bit pattern, when added to the original number (at the fixed length memory location), would make the result all zeros ? (at the same fixed length memory location). If we could come up with this bit pattern then that bit pattern would be the -ve representation (additive inverse) of the original number; as by definition adding a number to its additive inverse always results in zero. Example: take 5 which is 101 present inside a single 8 bit byte. Now the task is to come up with a bit pattern which when added to the given bit pattern (00000101) would result in all zeros at the memory location which is used to hold this 5 i.e. all 8 bits of the byte should be zero. To do that, start from the right most bit of 101 and for each individual bit, again ask the same question: What bit should I add to the current bit to make the result zero ? continue doing that taking in account the usual carry over. After we are done with the 3 right most places (the digits that define the original number without regard to the leading zeros) the last carry goes in the bit pattern of the additive inverse. Furthermore, since we are holding in the original number in a single 8 bit byte, all other leading bits in the additive inverse should also be 1's so that (and this is important) when the computer adds "the number" (represented using the 8 bit pattern) and its additive inverse using "that" storage type (a byte) the result in that byte would be all zeros.
1 1 1
----------
1 0 1
1 0 1 1 ---> additive inverse
---------
0 0 0
Many of the answers so far nicely explain why two's complement is used to represent negative numbers, but do not tell us what two's complement number is, particularly not why a '1' is added, and in fact often added in a wrong way.
The confusion comes from a poor understanding of the definition of a complement number. A complement is the missing part that would make something complete.
The radix complement of an n digit number x in radix b is, by definition, b^n-x.
In binary 4 is represented by 100, which has 3 digits (n=3) and a radix of 2 (b=2). So its radix complement is b^n-x = 2^3-4=8-4=4 (or 100 in binary).
However, in binary obtaining a radix's complement is not as easy as getting its diminished radix complement, which is defined as (b^n-1)-y, just 1 less than that of radix complement. To get a diminished radix complement, you simply flip all the digits.
100 -> 011 (diminished (one's) radix complement)
to obtain the radix (two's) complement, we simply add 1, as the definition defined.
011 +1 ->100 (two's complement).
Now with this new understanding, let's take a look of the example given by Vincent Ramdhanie (see above second response):
Converting 1111 to decimal:
The number starts with 1, so it's negative, so we find the complement of 1111, which is 0000.
Add 1 to 0000, and we obtain 0001.
Convert 0001 to decimal, which is 1.
Apply the sign = -1.
Tada!
Should be understood as:
The number starts with 1, so it's negative. So we know it is a two's complement of some value x. To find the x represented by its two's complement, we first need find its 1's complement.
two's complement of x: 1111
one's complement of x: 1111-1 ->1110;
x = 0001, (flip all digits)
Apply the sign -, and the answer =-x =-1.
I liked lavinio's answer, but shifting bits adds some complexity. Often there's a choice of moving bits while respecting the sign bit or while not respecting the sign bit. This is the choice between treating the numbers as signed (-8 to 7 for a nibble, -128 to 127 for bytes) or full-range unsigned numbers (0 to 15 for nibbles, 0 to 255 for bytes).
It is a clever means of encoding negative integers in such a way that approximately half of the combination of bits of a data type are reserved for negative integers, and the addition of most of the negative integers with their corresponding positive integers results in a carry overflow that leaves the result to be binary zero.
So, in 2's complement if one is 0x0001 then -1 is 0x1111, because that will result in a combined sum of 0x0000 (with an overflow of 1).
2’s Complements: When we add an extra one with the 1’s complements of a number we will get the 2’s complements. For example: 100101 it’s 1’s complement is 011010 and 2’s complement is 011010+1 = 011011 (By adding one with 1's complement) For more information
this article explain it graphically.
Two's complement is mainly used for the following reasons:
To avoid multiple representations of 0
To avoid keeping track of carry bit (as in one's complement) in case of an overflow.
Carrying out simple operations like addition and subtraction becomes easy.
Two's complement is one of the ways of expressing a negative number and most of the controllers and processors store a negative number in two's complement form.
In simple terms, two's complement is a way to store negative numbers in computer memory. Whereas positive numbers are stored as a normal binary number.
Let's consider this example,
The computer uses the binary number system to represent any number.
x = 5;
This is represented as 0101.
x = -5;
When the computer encounters the - sign, it computes its two's complement and stores it.
That is, 5 = 0101 and its two's complement is 1011.
The important rules the computer uses to process numbers are,
If the first bit is 1 then it must be a negative number.
If all the bits except first bit are 0 then it is a positive number, because there is no -0 in number system (1000 is not -0 instead it is positive 8).
If all the bits are 0 then it is 0.
Else it is a positive number.
To bitwise complement a number is to flip all the bits in it. To two’s complement it, we flip all the bits and add one.
Using 2’s complement representation for signed integers, we apply the 2’s complement operation to convert a positive number to its negative equivalent and vice versa. So using nibbles for an example, 0001 (1) becomes 1111 (-1) and applying the op again, returns to 0001.
The behaviour of the operation at zero is advantageous in giving a single representation for zero without special handling of positive and negative zeroes. 0000 complements to 1111, which when 1 is added. overflows to 0000, giving us one zero, rather than a positive and a negative one.
A key advantage of this representation is that the standard addition circuits for unsigned integers produce correct results when applied to them. For example adding 1 and -1 in nibbles: 0001 + 1111, the bits overflow out of the register, leaving behind 0000.
For a gentle introduction, the wonderful Computerphile have produced a video on the subject.
The question is 'What is “two's complement”?'
The simple answer for those wanting to understand it theoretically (and me seeking to complement the other more practical answers): 2's complement is the representation for negative integers in the dual system that does not require additional characters, such as + and -.
Two's complement of a given number is the number got by adding 1 with the ones' complement of the number.
Suppose, we have a binary number: 10111001101
Its 1's complement is: 01000110010
And its two's complement will be: 01000110011
Reference: Two's Complement (Thomas Finley)
I invert all the bits and add 1. Programmatically:
// In C++11
int _powers[] = {
1,
2,
4,
8,
16,
32,
64,
128
};
int value = 3;
int n_bits = 4;
int twos_complement = (value ^ ( _powers[n_bits]-1)) + 1;
You can also use an online calculator to calculate the two's complement binary representation of a decimal number: http://www.convertforfree.com/twos-complement-calculator/
The simplest answer:
1111 + 1 = (1)0000. So 1111 must be -1. Then -1 + 1 = 0.
It's perfect to understand these all for me.